Buy OEM Mercedes-Benz Step Rails
Drive, say, a Mercedes-Benz SUV, like GLE 350? With a near-towering ground clearance -- 8 inches, if it's the 2024 model -- your ride's probably a little tough to get into and out of. If you've installed a lift kit, though, it can be even tougher. Luckily, here at MB Part Source, we've got the upgrade you need: step rails (running boards), at competitive pricing. Order today -- you'll have them put on in no time; we ship fast, all over the US. Contact us if you have any questions.
End Stop
Mercedes-Benz
202-352-00-46
Rear subframe to frame floor unit,rear.
$4.55
MSRP $6.25
Save $1.70
27.2% Off 
Stop Plug
Mercedes-Benz
009-988-03-78
Left. Ledge to front door.
$1.75
MSRP $2.40
Save $0.65
27.1% Off 
End Stop
Mercedes-Benz
2023520346
Axle housing to rear subframe,rear. Rubber mount.
$11.32
MSRP $15.50
Save $4.18
27% Off 
Hexalobular Screw
Mercedes-Benz
000000-001476
Pneumatic spring to flap.
$1.97
MSRP $2.70
Save $0.73
27% Off 
Tapping Screw
Mercedes-Benz
000000-000528
Panelling to front panel 4,8x16. 4,8x16.
$1.76
MSRP $2.40
Save $0.64
26.7% Off 
Clamp
Mercedes-Benz
000-995-31-65
Brake line to left front wheelhouse panel. Spacer for brake lines to partition. Brake line mount to hydraulic unit. Brake line to...
$4.31
MSRP $6.00
Save $1.69
28.2% Off 
Tapping Screw
Mercedes-Benz
000000-000460-64
License plate to front bumper.
$1.35
MSRP $1.90
Save $0.55
28.9% Off 
Tapping Screw
Mercedes-Benz
000000000544
Bumper at fender, left and right. 3x25 diameter: 6,3mm thread code letter: r. Mount, front trim. 3X25 Diameter: 6,3mm Thread code letter:...
No results found for "step rail, side rail, running board". Here are some helpful search tips:
- Search by a part name. Example: water pump.
- Be less specific. Example: brake instead of ceramic brake.
- Remove information such as make, year or model.
- Can't find the part you are looking for? Contact us and we'll find it for you!
How to Install Mercedes-Benz Step Rails (Running Boards) DIY
You're in luck; they're pretty easy to put on. Here's how to do it.
- Gather what you'll need. That means safety glasses, a flashlight, and a wax pencil, plus wrench, ratchet, and socket sets, an impact driver, a drill, drill bits, and a flat screwdriver or punch. You'll also need wheel chocks and, most likely, a little touch-up paint.
- Use the wax pencil to mark a. the mounting holes under your vehicle, and b. where any holes need to be drilled, for each of the rails' brackets.
- Use the drill and the proper-size drill bit to make any holes necessary.
- Put the fasteners in place, align the brackets, and finger-tighten the fasteners (just not completely).
- Align the mount holes on one of the rails with the brackets. Then, place the fasteners and finger-tighten them.
- Finish tightening all the fasteners using either the right-size ratchet and wrench or the impact driver. (Be sure not to overtighten them.) Watch your alignment as you go; adjust it as needed.
- Repeat these steps for the rest of the rails.
If you end up needing to drill holes for fasteners, you'll want to touch up the metal around them afterward. Be sure to consult your owner's manual for specific directions on everything, as they can vary among Mercedes-Benz models. As always, if you're not sure how to install, a Mercedes-Benz service center will be glad to help.